TRACK DRIVE RC/CORE DRILL

max

(depth in metres)

HC1000T

Configure Your Custom Hydracore

reset to base model

  • Options:

    Base Model

    Power

    • Hatz 75Hp T3 Turbo Diesel
      • Rubber mounted

    Track Drive System

    • Light Weight Track Drive System
    • Eaton two speed final drives
    • Wireless Remote Control Tramming with “back up” wired harness

    Heli-Transport

    • Drill designed to separate into 4 sections under 2000lb (900kg) for Heli Transport in less than 45 minutes

    Drill Head

    • Hydracore Top Drive Drill Head with “integrated” water swivel
      • Quick change water swivel seal system
      • Quick release swing out design to clear wireline

    Drilling Features

    • Hydraulic rod pulling with the drill head – Axial Pull 17,000lb (7700Kg)
    • Hydraulic feed control with 70” (1.78M) stroke
    • Hydraulic Mast Raise
    • Rotation Safety Guard

    Winch

    • Wireline Winch 900ft (275M)

    Footclamp

    • Hydraulic Foot Clamp B – P size – Axial Capacity 17,000lb (7700Kg)

    Controls

    • Fold open Control Panel for ease of maintenance
    • Direct Hydraulic Drill Controls – 45GPM (170 Lpm)
    • E-Stop located in the control panel, by the Drill Helper and on the wireless remote
    • Hydraulic controls provided for Water Pump and Mudmixer
    • Water Tree with dump valve
  • POWER

    • Hatz 75HP T3 Turbo Diesel
    • Hatz 75HP T4 Turbo Diesel
    • Hatz 75HP T5 Turbo Diesel
    • Three Kubota 30HP T2 Turbo Diesel – Total 90HP
    • Three Kubota 40HP T2 Turbo Diesel – Total 120HP
  • Safety

    • Auto Rotation Shutdown
    • Pedestal Mounted Secondary E-Stop
  • Drill Head Motors

    • HYD DRIVE MOTOR 1925 RPM
    • HYD DRIVE MOTOR 1650 RPM
    • HYD DRIVE MOTOR 1450 RPM
    • HYD DRIVE MOTOR 1150 RPM
    • HYD DRIVE MOTOR 975 RPM
    • HYD DRIVE MOTOR 575 RPM
    • CASING MOTOR 22.8 CI, 450 RPM
  • Winches & Hoists

    • Wire Line Winch 900ft (275M)
    • Wire Line Winch 2000ft (600M)
  • Mud Mixer

    • MUD MIXER, HYDRAULIC
  • PUMPS

    • WATER PUMP 20GPM DIESEL, AB100
      • Diesel supply pump to move water from the source to the pressure pump. For long distance and elevation multiple pumps may be required.
    • WATER PUMP 20GPM HYD, AB100
      • Suited for rod sizes up to B, can be used for N but with increased time to pump the Inner Tube
    • WATER PUMP 40GPM HYD, KF50
      • Suited for rod sizes up to P
  • Summary

Email My Summary

Type: (mandatory)


Choose Hydracore
you owe it to your bottom line

Powerful Turbo-Diesel Engine

Equipped with smooth running 75Hp Hatz Turbo Diesel, this rig is offered emission standards T2, T3, T4 and T5.

Helicopter Portable – Under 2000 lb lifts!

The HC1000T was designed from the ground up for Heli-portable drilling. The drill separates into 4 sections that are each under 2000lb. Through innovative engineering including our custom hose bulkheads, these machines can be assembled in under an hour.

DOUBLE BREAKOUT FOOTCLAMP

No need for Pipe wrenches on this rig! The powerful double-breakout footclamp can separate even the most stubborn rod joints.

On Board Water Pump

Keeping with our maintenance friendly designs our drills offer adjustable saddle bearings. These are adjusted in several minutes allowing you to focus on putting core in the box.

Rugged Track System

The custom track system is the lightest of its kind in the world. The track is equipped with a 2 speed Eaton final drive. Float over the softest terrain as the large surface area of the track allows for a very low ground pressure and minimal disturbance to the environment, while delivering excellent performance in virtually any terrain.

Remote Control

Safety is paramount with all Hydracore Products. Our remote-control Tramming system requires no tether or cords. This allows the operator to work comfortably out of harm’s way in the most difficult terrain.

Ease of Access

All hydraulic equipment needs attention at some point. Our innovative control panel is designed to hinge open and expose all components for ease of maintenance and cleaning.

Detailed Specifications

  • HC1000T
  • Imperial
  • Metric
  • Move Method
  • Track, Truck, Helicopter
  • Drill Method
  • Core (A, B, N, H), RC (3.5, 4.5in), Auger
  • Power
  • 75HP
  • 56KW
  • Drill Torque
  • 800ft-lbs
  • 1080Nm
  • Pull Back
  • 17000lb
  • 7700Kg
  • Feed Stroke
  • 70″
  • 1.78M
  • Rod Length
  • 5ft
  • 1.5M
  • Rod Pull Length
  • 5ft
  • 1.5M
  • Max. Weight/Move
  • 1800lb
  • 816Kg
  • Total Weight
  • 6000lb
  • 2720Kg