SURFACE CORE DRILL

recommended

max

(depth in metres)

HC2000

Configure Your Custom Hydracore

reset to base model

  • Options:

    Base Model

    Power

    • Four Kubota 30HP T2 Turbo Diesels – Total 120HP
      • Rubber mounted in aluminum frames with radiator guards
      • All engine throttle controls tied to one lever at the control panel

    Drill Module

    • Lightweight aluminum drill skid
    • Hydraulic Mast Raise with locking support legs
    • Rotation Safety Guard
    • Three Piece Drill Mast
    • Uses 10ft (3M) Drill Rods
    • Pull Rods up to 20ft (6M) length
    • Hydraulic rod pulling with the drill head – Axial Pull 24,000lb (10900Kg)
    • Hydraulic feed control with 70” (1.78M) stroke

    Drill Head

    • Hydracore Variable Speed “H” size Drill Head and Link Chuck
      • Proprietary “link design” one jaw size fits all rod sizes
      • Low maintenance chuck with no release bearings on internal cylinders
      • Quick release swing out design to clear wireline
      • Carbon Belt Drive

    Footclamp

    • Hydraulic Foot Clamp B – P size – Axial Capacity 24,000lb (10900Kg)

    Hydraulic Control Module

    • Fold open Control Panel for ease of maintenance
    • Direct Hydraulic Controls – 90GPM (340 Lpm)
    • Single E-Stop located in the control panel
    • Hydraulic controls provided for auxiliary Water Pump and Mudmixer
    • Water Tree with dump valve
    • Hydraulic module splits into two sections for decreased weight during mobilization

  • Power

    • Isuzu 130HP T2 Turbo Diesel
    • Two Hatz 75HP T4 Turbo Diesel – Total 150HP
    • Two Hatz 75HP T5 Turbo Diesel – Total 150HP
    • Four Kubota 30HP T2 Turbo Diesels – Total 120HP (standard)
    • Four Kubota 40HP T2 Turbo Diesel – Total 160HP

  • Safety

    • Auto Rotation Shutdown
    • Pedestal Mounted Secondary E-Stop
    • Rod Handling

  • Drill Head

    • Hydracore “P” size head with 50,000lb (22,675Kg) axial holding capacity proprietary chuck

  • Winches & Hoists

    • Rod Hoist
    • Wire Line Winch 2000ft (600M)
    • Wire Line Winch with Level Wind System 2000ft (600M)
    • Wire Line Winch with Level Wind System 5000ft (1500M)

  • Mud Mixer

    • MUD MIXER, HYDRAULIC

  • PUMPS

    • WATER PUMP 20GPM DIESEL, AB100
      • Diesel supply pump to move water from the source to the pressure pump. For long distance and elevation multiple pumps may be required.
    • WATER PUMP 40GPM HYD, KF50
      • Suited for rod sizes up to P
    • WATER PUMP 40GPM HYD, Bean 435
      • Suited for rod sizes up to P

  • Skids & Shacks

    • Steel Drill Skid
    • Drill Shack with Steel Skid
    • Drill Shack – Winterized with Skid

  • Transport

    • Tracked Drill Carrier with Crane

  • Summary

Email My Summary

Type: (mandatory)


My HC2000

    Base Model

    Power

    • Four Kubota 30HP T2 Turbo Diesels – Total 120HP
      • Rubber mounted in aluminum frames with radiator guards
      • All engine throttle controls tied to one lever at the control panel

    Drill Module

    • Lightweight aluminum drill skid
    • Hydraulic Mast Raise with locking support legs
    • Rotation Safety Guard
    • Three Piece Drill Mast
    • Uses 10ft (3M) Drill Rods
    • Pull Rods up to 20ft (6M) length
    • Hydraulic rod pulling with the drill head – Axial Pull 24,000lb (10900Kg)
    • Hydraulic feed control with 70” (1.78M) stroke

    Drill Head

    • Hydracore Variable Speed “H” size Drill Head and Link Chuck
      • Proprietary “link design” one jaw size fits all rod sizes
      • Low maintenance chuck with no release bearings on internal cylinders
      • Quick release swing out design to clear wireline
      • Carbon Belt Drive

    Footclamp

    • Hydraulic Foot Clamp B – P size – Axial Capacity 24,000lb (10900Kg)

    Hydraulic Control Module

    • Fold open Control Panel for ease of maintenance
    • Direct Hydraulic Controls – 90GPM (340 Lpm)
    • Single E-Stop located in the control panel
    • Hydraulic controls provided for auxiliary Water Pump and Mudmixer
    • Water Tree with dump valve
    • Hydraulic module splits into two sections for decreased weight during mobilization

    • power

    • Isuzu 130HP T2 Turbo Diesel
    • Two Hatz 75HP T4 Turbo Diesel – Total 150HP
    • Two Hatz 75HP T5 Turbo Diesel – Total 150HP
    • Four Kubota 30HP T2 Turbo Diesels – Total 120HP (standard)
    • Four Kubota 40HP T2 Turbo Diesel – Total 160HP

    • safety

      *A rotation Safety Guard and operator E-Stop come as standard*

    • Auto Rotation Shutdown
    • Pedestal Mounted Secondary E-Stop
    • Rod Handling

    • drill head

    • Hydracore “P” size head with 50,000lb (22,675Kg) axial holding capacity proprietary chuck

    • winches & hoists

    • Rod Hoist
    • Wire Line Winch 2000ft (600M)
    • Wire Line Winch with Level Wind System 2000ft (600M)
    • Wire Line Winch with Level Wind System 5000ft (1500M)

    • mud mixer

    • MUD MIXER, HYDRAULIC

    • pumps

    • WATER PUMP 20GPM DIESEL, AB100
      • Diesel supply pump to move water from the source to the pressure pump. For long distance and elevation multiple pumps may be required.
    • WATER PUMP 40GPM HYD, KF50
      • Suited for rod sizes up to P
    • WATER PUMP 40GPM HYD, Bean 435
      • Suited for rod sizes up to P

    • skids & shacks

    • Steel Drill Skid
    • Drill Shack with Steel Skid
    • Drill Shack – Winterized with Skid

    • transport

    • Tracked Drill Carrier with Crane

    Email My Summary

    Type: (mandatory)


    Choose Hydracore
    you owe it to your bottom line

    Powerful Turbo-Diesel Engine

    Options ranging from 120 – 160Hp. These are available in single, double, triple, and quad engine configurations to suit Man-portable, Truck-portable and Heli-portable drilling.

    Proprietary Drill Head

    Our H sized Drill Head is rated to withstand up to 200hp and 30,000 lbs of pull-back. We have eliminated the main sources of Drill Head failures including the chuck release bearing, internal opening cylinder, and gear transmission.

    Fail proof Footclamp

    Footclamps require incredible holding power. At the same time, they need to be easy to maintain and operate. While others opt to use overly complex “chucks”, the innovative Hydracore footclamps use two standard hydraulic cylinders. The cylinders on this HW (P) sized clamp can hold up to 25,000 lbs and one set of jaws works for all rod sizes!

    Adjustable Saddle Bearings

    Keeping with our maintenance-friendly designs our drills offer adjustable saddle bearings. These are adjusted in several minutes allowing you to focus on putting more “core in the box”.

    Direct Acting Hydraulic Control

    Direct acting hydraulics are the gold standard in the industry. We design all drilling functions for direct control, optimal reliability, and maximum uptime.

    Ease of Access

    All hydraulic equipment needs attention at some point. Our innovative control panel is designed to hinge open and expose all components for ease of maintenance and cleaning.

    HC2000 2 engine

    HC2000 4 engine

    HC2000 2 drill

    Detailed Specifications

    HC2000MP

    • HC2000MP
    • Imperial
    • Metric
    • Move Method
    • Man power, Helicopter, Truck
    • Drill Method
    • Core (B, N, H)
    • Power
    • 120 – 160HP
    • 90 – 120KW
    • Drill Torque
    • 1250ft-lbs
    • 1700Nm
    • Pull Back
    • 24000lb
    • 10900Kg
    • Feed Stroke
    • 70″
    • 1.78M
    • Rod Length
    • 10ft
    • 3M
    • Rod Pull Length
    • 20ft
    • 6M
    • Max. Weight/Move
    • 580lb
    • 260Kg
    • Total Weight
    • 3860lb
    • 1750Kg

    HC2000HP

    • HC2000HP
    • Imperial
    • Metric
    • Move Method
    • Helicopter, Truck
    • Drill Method
    • Core (B, N, H)
    • Power
    • 130HP
    • 97KW
    • Drill Torque
    • 1250ft-lbs
    • 1700Nm
    • Pull Back
    • 24000lb
    • 10900Kg
    • Feed Stroke
    • 70″
    • 1.78M
    • Rod Length
    • 10ft
    • 3M
    • Rod Pull Length
    • 20ft
    • 6M
    • Max. Weight/Move
    • 1100lb
    • 500Kg
    • Total Weight
    • 3860lb
    • 1750Kg