SONIC/CORE DRILL

recommended

max

(depth in metres)

HC5000S

Configure Your Custom Hydracore

reset to base model

  • Options:

    Base Model

    Power

    • Isuzu 190HP T2 Turbo Diesel
    • Screw system for ease of removing the engine for heli-transport
    • Radiator Guard

    Drill Module

    • Built in Jib crane – 2000lb (900Kg) capacity
    • Lightweight drill skid
    • Two Piece Drill Mast
    • Uses 10ft (3M) Drill Rods
    • Hydraulic rod pulling with the drill head – Axial Pull 24,000lb (9050Kg)
    • Hydraulic feed control with 138” (3.5M) stroke
    • Hydraulic Mast Raise with locking support legs
    • Rotation Safety Guard

    Drill Head

    • Industry Leading Boart Longyear LS250 Sonic drill Head
      • 75 Hz and 41,000lb force
    • Drill Head 30 Degree side swing for ease of removing sonic samples
    • Quick Change Drill Head system
      • 30 minute Drill Head change over

    FootClamp

    • Hydraulic Double Foot Clamp with Rod Break 2 3/8 – 11” size – Axial Capacity 24,000lb (9050Kg)

    Hydraulic Control Module

    • Fold open Control Panel for ease of maintenance
    • Direct Hydraulic Controls – 100GPM (380 Lpm)
    • Single E-Stop located in the control panel
    • Hydraulic controls provided for auxiliary Water Pump and Mudmixer
    • Water Tree with dump valve

  • Power

    • Isuzu 190HP T2 Turbo Diesel (standard)
    • Isuzu 203HP T3 Turbo Diesel

  • Safety

    • Auto Rotation Shutdown
      • When the rotation guard door is opened the Drill Head is prevented from turning. Built from safety rated sensors and relays.
    • Pedestal Mounted Secondary E-Stop
      • The secondary e-stop can be placed by the “drill helper” for an additional level of safety

  • Drill Head & SPT

    • Add on – Hydracore “H” size Core Drill Head
      • Includes proprietary “Link Chuck” with 30,000lb (13,600Kg) axial holding capacity
    • Add on – Hydracore “P” size Core Drill Head
      • Includes proprietary Chuck with 50,000lb (22,675Kg) axial holding capacity
    • Add on – Marl SPT Auto-hammer system
      • Used for Geotechnical soil penetration testing

  • Winches & Hoists

    • Rod Hoist
      • Used for hoisting using the water swivel
    • Wire Line Winch 2000ft (600M)
    • Wire Line Winch with Level Wind System 2000ft (600M)
      • Level wind systems are required on some job sites, please check with your client for your specific needs.
    • Wire Line Winch with Level Wind System 5000ft (1500M)
      • Level wind systems are required on some job sites, please check with your client for your specific needs.

  • Mud Mixer

    • MUD MIXER, HYDRAULIC
      • It is recommended to use two Mud Mixers, one for Mud and one for Polymers.

  • PUMPS

    • WATER PUMP 20GPM DIESEL, AB100
      • Diesel supply pump to move water from the source to the pressure pump. For long distance and elevation multiple pumps may be required.
    • WATER PUMP 20GPM HYD, AB100
      • Suited for rod sizes up to B, can be used for N but with increased time to pump the Inner Tube
    • WATER PUMP 40GPM HYD, KF50
      • Suited for rod sizes up to P
    • WATER PUMP 40GPM HYD, Bean 435
      • Suited for rod sizes up to P

  • SKIDS & SHACKS

    • Steel Drill Skid
      • Direct mounting for the Drill, Powerpack and Rod Sloop
      • Minimum requirement for Rod Handling option
    • Drill Shack with Steel Skid
      • Direct mounting for the Drill, Powerpack and Rod Sloop
      • Man door
      • Engine access side door
      • Upgraded requirement for Rod Handling option
    • Drill Shack – Winterized with Skid
      • Direct mounting for the Drill, Powerpack and Rod Sloop
      • Upgraded requirement for Rod Handling option
      • Man door
      • Engine access side door

  • Transport

    • Tracked Drill Carrier with Crane
      • Built on a rugged Morooka MS800 Chassis
      • Ability to carry the drill, power pack as well as general materials transport to site

  • Summary

Email My Summary

Type: (mandatory)


My HC5000S

    Base Model

    Power

    • Isuzu 190HP T2 Turbo Diesel
    • Screw system for ease of removing the engine for heli-transport
    • Radiator Guard

    Drill Module

    • Built in Jib crane – 2000lb (900Kg) capacity
    • Lightweight drill skid
    • Two Piece Drill Mast
    • Uses 10ft (3M) Drill Rods
    • Hydraulic rod pulling with the drill head – Axial Pull 24,000lb (9050Kg)
    • Hydraulic feed control with 138” (3.5M) stroke
    • Hydraulic Mast Raise with locking support legs
    • Rotation Safety Guard

    Drill Head

    • Industry Leading Boart Longyear LS250 Sonic drill Head
      • 75 Hz and 41,000lb force
    • Drill Head 30 Degree side swing for ease of removing sonic samples
    • Quick Change Drill Head system
      • 30 minute Drill Head change over

    FootClamp

    • Hydraulic Double Foot Clamp with Rod Break 2 3/8 – 11” size – Axial Capacity 24,000lb (9050Kg)

    Hydraulic Control Module

    • Fold open Control Panel for ease of maintenance
    • Direct Hydraulic Controls – 100GPM (380 Lpm)
    • Single E-Stop located in the control panel
    • Hydraulic controls provided for auxiliary Water Pump and Mudmixer
    • Water Tree with dump valve

    • power

    • Isuzu 190HP T2 Turbo Diesel (standard)
    • Isuzu 203HP T3 Turbo Diesel

    • safety

      *A rotation Safety Guard and operator E-Stop come as standard*

    • Auto Rotation Shutdown
      • When the rotation guard door is opened the Drill Head is prevented from turning. Built from safety rated sensors and relays.
    • Pedestal Mounted Secondary E-Stop
      • The secondary e-stop can be placed by the “drill helper” for an additional level of safety

    • drill head & spt

      *A LS250 Sonic Head comes as standard *

    • Add on – Hydracore “H” size Core Drill Head
      • Includes proprietary “Link Chuck” with 30,000lb (13,600Kg) axial holding capacity
    • Add on – Hydracore “P” size Core Drill Head
      • Includes proprietary Chuck with 50,000lb (22,675Kg) axial holding capacity
    • Add on – Marl SPT Auto-hammer system
      • Used for Geotechnical soil penetration testing

    • winches & hoists

    • Rod Hoist
      • Used for hoisting using the water swivel
    • Wire Line Winch 2000ft (600M)
    • Wire Line Winch with Level Wind System 2000ft (600M)
      • Level wind systems are required on some job sites, please check with your client for your specific needs.
    • Wire Line Winch with Level Wind System 5000ft (1500M)
      • Level wind systems are required on some job sites, please check with your client for your specific needs.

    • mud mixer

    • MUD MIXER, HYDRAULIC
      • It is recommended to use two Mud Mixers, one for Mud and one for Polymers.

    • pumps

    • WATER PUMP 20GPM DIESEL, AB100
      • Diesel supply pump to move water from the source to the pressure pump. For long distance and elevation multiple pumps may be required.
    • WATER PUMP 20GPM HYD, AB100
      • Suited for rod sizes up to B, can be used for N but with increased time to pump the Inner Tube
    • WATER PUMP 40GPM HYD, KF50
      • Suited for rod sizes up to P
    • WATER PUMP 40GPM HYD, Bean 435
      • Suited for rod sizes up to P

    • skids & shacks

    • Steel Drill Skid
      • Direct mounting for the Drill, Powerpack and Rod Sloop
      • Minimum requirement for Rod Handling option
    • Drill Shack with Steel Skid
      • Direct mounting for the Drill, Powerpack and Rod Sloop
      • Man door
      • Engine access side door
      • Upgraded requirement for Rod Handling option
    • Drill Shack – Winterized with Skid
      • Direct mounting for the Drill, Powerpack and Rod Sloop
      • Upgraded requirement for Rod Handling option
      • Man door
      • Engine access side door

    • transport

    • Tracked Drill Carrier with Crane
      • Built on a rugged Morooka MS800 Chassis
      • Ability to carry the drill, power pack as well as general materials transport to site

    Email My Summary

    Type: (mandatory)


    Choose Hydracore
    you owe it to your bottom line

    Powerful Turbo Diesel Engine

    Equipped with smooth running 203Hp Isuzu Turbo Diesel, this rig is offered emission standards T2, T3 and T4.

    ls250 sonic drilling rig - Hydracore

    Industry Leading LS250 Sonic Drill Head

    We offer our Sonic Drill with the most reliable drill head on the market. Tuned by Hydracore to produce 75Hz and 41,000lbs of output force. Optional Hydracore Core Drill heads are offered in both “H” and “P” sizes. The Head system allows for a 30 minute change over using the included jib crane.

    Double Breakout Footclamp

    No need for Pipe wrenches on this rig! The powerful double breakout footclamp can separate even the most stubborn rod joints. The clamp Jaws hold up to 12” rods and casing securly using a hydraulic synchronizing system and accumulators.

    Adjustable Saddle Bearings

    Keeping with our maintenance friendly designs our drills offer adjustable saddle bearings. These are adjusted in several minutes allowing you to focus on putting core in the box.

    Direct Acting Hydraulic Control

    Its no secret in the industry that direct acting hydraulics are bullet proof and unsurpassed in reliability. We design all drilling functions for direct control and maximum uptime.

    Ease of Access

    Let’s face it all hydraulic equipment needs attention at some point. Our innovative control panel is designed to hinge open and expose all components for ease of maintenance and cleaning.

    HC5000S engine

    HC5000S drill

    Detailed Specifications

    • HC5000S
    • Imperial
    • Metric
    • Move Method
    • Truck, Helicopter
    • Drill Method
    • Sonic, Core (A, B, N, H, P)
    • Power
    • 200HP Diesel
    • 150KW
    • Drill Torque
    • 1700ft-lbs
    • 2300Nm
    • Pull Back
    • 20000lb
    • 9050Kg
    • Feed Stroke
    • 138″
    • 3.5M
    • Rod Length
    • 10ft
    • 3M
    • Rod Pull Length
    • 10ft
    • 3M
    • Max. Weight/Move
    • 1800lb
    • 816Kg
    • Total Weight
    • 7500lb
    • 3400Kg